Step 1: Identify Your Target Lift Area

Stand in front of a mirror with your hair pulled back. Using your fingertips, gently press and pull the skin just in front of your ears. Experiment by pulling upward or diagonally until you see a natural-looking lift in the face or neck area that flatters your features.

This is your target lift zone—the area where you will apply the invisible facelift tapes.

📍 Important:

Position the tape so that when the bands and prongs are connected, they will be hidden underneath your hair, wig, or head covering for a seamless and discreet finish.

Step 2: Prep Your Skin for Strong, Lasting Hold

Before applying the tapes, it’s crucial to prep your skin properly to ensure maximum adhesion and all-day lift.

✔️ Cleanse Thoroughly – Wash your face and neck with a gentle cleanser to remove dirt, sweat, and product buildup.

✔️ Remove All Oils and Makeup – The tapes will not stick to oily or makeup-covered skin. Be sure your skin is completely makeup-free and oil-free.

✔️ Use Rubbing Alcohol – For best results, apply rubbing alcohol with a cotton pad to the areas where the tapes will be placed. This eliminates any leftover residue and gives the adhesive a clean surface to grip.

⚠️ Do not moisturize or apply any skincare products—even lightweight serums or sunscreens—in the areas where the tape will be applied.

💡 Proper prep is the secret to a firm, invisible hold that lasts all day.

Step 3: Prepare the Invisible Tape for Application

Now it’s time to get your Snatch & Go Invisible Tape ready for action.

🟤 Insert the SnatchProng First

Carefully take one facelift prong (attached to your band) and insert it into the designated hole on the sticky side of the tape. The prong should go through the small pre-cut slit—this will lock the tape securely in place once applied.

⚠️ Important: Do NOT remove the backing of the tape yet.

Leave the protective backing on the adhesive side until you are completely ready to place the tape on your target area.

✅ Check Prong Position

Make sure the metal prong remains on the outer side of the tape (facing away from the skin). This setup ensures a clean connection and maximum hold once the tape is applied.

🔒 This step locks the tape to your band securely—keeping everything in place once you're snatched!

Step 4: Apply the Invisible Tape to the Face

With your skin prepped and the prong inserted, you’re ready to apply the Invisible Tape to your chosen lift area.

🟤 Peel Off the Backing

Carefully remove the backing from the adhesive side of the tape—only when you’re fully ready to apply it.

📍 Place Precisely on Cleaned Skin

Gently but firmly press the sticky side of the tape onto your pre-determined target area on the upper and/or lower face.

Be sure the tape sits smoothly on the skin with no wrinkles or gaps for a natural look and strong grip.

✋🏽 Press & Set

Hold the tape in place with your fingers and press firmly. Allow it to set on the skin for 5 to 10 minutes. This “setting time” allows the adhesive to bond properly to your skin for a long-lasting hold.

💡 Do not stretch or connect the bands just yet—this wait time ensures maximum lift and wear time once the bands are pulled.

Step 5: Connect the Upper Face Bands Behind the Head

Now it’s time to create your upper face lift using the 4-Loop Band and the 3-Inch Connecting Band.

🪮 Part & Pin Hair for Access

Begin by parting a section of your hair at the crown or toward the back of your head—where the bands will rest. Use clips or bobby pins to keep your hair out of the way while you work.

🟤 Insert Prongs Into the SnatchLoops

Take one end of the band and insert the prong into one of the 4 SnatchLoops on the loop band.

💡 The loop you choose will determine how tight or lifted the final result will be—start with the middle loop for a natural look and adjust as needed.

🔗 Connect with the 3-Inch Band

Use the 3-Inch Band to connect both sides of the 4-Loop Band together behind your head. This short band provides the tension needed to hold your lift in place.

🔒 Use the Hair Clip Anchor (Optional)

If needed, secure the top band in place using the provided clip to anchor it discreetly to your hair. This helps prevent slippage and adds extra hold for longer wear.

👀 Always aim for a natural, comfortable lift—not overly tight. The goal is snatched and seamless!

Step 6: Connect the Lower Face Bands Behind the Head

This final step targets the lower face and jawline, giving you that beautifully lifted, contoured look.

🟤 Use Both 5-Inch Bands for the Chin Area

Take the two 5-Inch Bands and position them just below each ear, where the skin naturally starts to lose firmness around the jawline.

🔗 Connect to the Upper Band Loops

Insert each prong into matching loops on opposite sides of the top band (the same 4-Loop Band used in Step 5).

This creates a balanced and even lift from the chin upward, tightening the jawline and enhancing definition.

💡 Adjust the Loop for Desired Tension

Just like with the upper bands, your choice of loop will control the intensity of the lift. Start with a mid-range loop and adjust for comfort and a natural appearance.

✔️ Make sure the lift looks smooth and not overly tight. The goal is a refreshed, youthful look—not pulled or artificial.

🎉 You're officially snatched! Style your hair, step back, and enjoy your sculpted, lifted new look.